Old Product Code: PM-60.05.4Y.B New Product Code: WL-223-0018

PM series balances are equipped with an innovative measuring system based on radwag monoblock technology. This enables operation with readability of 0.01g at capacity of 15kg, and with readability of 0.1g at capacity of 50 kg. Use of the new measuring system, which is a subject matter of radwag patent, guarantees stability of repeatability over time at a range.

• Unrivalled repeatability of indications.
• Weighing of heavy loads with maximum accuracy.
• Fast mass measurements.
• New RADWAG MonoBLOCK sensor.
• Robust mechanical design – new lower weighing platform.
• Improved ergonomics – two types of weighing terminal for selection.

• Autotest: Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.
• Dosing: Weighing process for which reference mass has been determined together with tolerance for its determination. Dosing tolerance is given in [%] and it is calculated in relation to the reference value thus being a permissible deviation of this process. This solution is used for weighing powders, liquids and loose materials. Dosing function performance is often supported with bar graph - load indicator. For industrial scales it is possible to use a control systems of dosing process.
• Percent Weighing: Percent Weighing function is used for comparison of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly exceeded.
• Parts Counting: Function using mass measurement for determination of measured items quantity. Mass of a single item is required for this process. It may be either estimated through Weighments or taken from a database. For items counting the following algorithm is used: all items mass/single item mass = quantity. Function operation is supported by a mechanism of Automatic Correction of Accuracy. This allows to update single item mass in course of the process. To a certain extend Automatic Correction of Accuracy eliminates error which may be a result of different mass values of seemingly alike single elements. For industry solutions items counting may be simultaneously carried out with check weighing and dosing thus industry solutions feature audio signaling base informing that specified number of items has been weighed. It is possible to apply weighing systems using few platforms of different MAX capacities and different accuracies.
• Formulation: Function supporting the mixture making process, wherein the mixture contains various components. Formulation function usually uses the balance/scale database of components. Formulation serves for monitored check weighing of every single component with a given tolerance. It is enriched with a set of individual settings.
• Statistics: Statistics function registers and analyses performed measurements. This supplies the user with the following information: Max and Min standard deviation, average value, variance, range et.
• Check weighing: Check weighing function is used for checking whether the measured sample mass is within the predefined threshold values, Low [LO] and High [HI]. The thresholds are given in [g] and [kg] units. Current state of a sample being measured is signaled by means of pictograms located on a display for laboratory balances, for industrial scales stack light System is used. This visual +/- inspection is in operation during segregation, control or packing process of products for which mass has bees determined with a specified tolerance, e.g. 12860 g 961
• IR Sensors: Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.
• GLP Procedures: Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.
• Animal Weighing: Process of mass determination for a product which may unwillingly reposition within the weighing pan. Mass determination in such cases requires much longer period of time when compared to typical weighing process. It is the user who defines period of time needed for control of measured product mass. The user can thus optimize the function depending on the measured product characteristics.
• Air Density Correction: Function performing correction of mass measurement indication, wherein the air density is taken into account. It is used in balances with reading unit < 0,01 mg.
• Statistical Quality Control: Statistical control for determination of basic statistical criteria - maximum, minimum, standard deviation, mean values for each batch, etc.

• Capacity x Readability: 60kg x 0.5g
• Tare range: –60kg
• Repeatability (5% Max): 0.2g
• Repeatability (Max): 0.4g
• Linearity: ± 1.5g
• Sensitivity temperature drift: 2 x 10-6/°C x Rt
• Minimum weight (U=1%, k=2): 41g
• Minimum weight (USP): 410g
• Adjustment: Internal Calibration
• Stabilization time: 3s
• Indicator fastening: 1.5m cable (Standard Models)
• Terminal mode: 4Y Terminal
• Display: 5.7" color, resistive touch screen
• Keypad: 8 keys
• Protection class: IP 43
• Databases: 19
• Touch-free operation: 2 programmable proximity sensors
• USB-A: 2
• RS232: 2
• Ethernet: 10/100 Mbit
• Wireless connection: 802.11 b/g/n
• IN/OUT: 4 x in, 4 x out
• Power supply: 3.5 ÷ 16V DC
• Power consumption: 15W
• Operating temperature: +10 ÷ +40°C
• Atmospheric humidity: 40 ÷ 80 %
• Transport and storage temperature: –10 ÷ +50°C
• Weighing pan dimensions: 500 x 400mm
• Weighing device dimensions: 640 x 400 x 115mm
• Packaging dimensions: 700 x 600 x 200mm
• Net weight/Gross weight: 17kg/19kg

• 2-Year Warranty